Table of Contents
Supported Devices
Banana Pi M1
Status: fully supported (stable)
Remarks:
none
Name | Banana Pi |
---|---|
SoC | Allwinner A20 |
CPU | ARM Cortex-A7 Dual-Core 1GHz |
GPU | ARM Mali400 MP2 |
RAM | 1 GB DDR3 |
Ethernet | 1 x 10/100/1000Mbps (Realtek RTL8211E/D) |
Wifi | none |
Storage | SD card, SATA 2.0 |
USB | 2 x USB 2.0 host, 1 x USB 2.0 OTG |
GPIO header | 26 pins |
Banana Pro
Status: fully supported (stable)
Remarks:
How to enable Wifi (depending on your kernel):
Kernel 3.4.x: Select the Banana Pro in 'bananian-hardware', add 'ap6210' to /etc/modules and reboot.
Kernel 4.x: Run 'aptitude install u-boot-pro-bananian' and reboot.
Name | Banana Pro |
---|---|
SoC | Allwinner A20 |
CPU | ARM Cortex-A7 Dual-Core 1GHz |
GPU | ARM Mali400 MP2 |
RAM | 1 GB DDR3 |
Ethernet | 1 x 10/100/1000Mbps (Realtek RTL8211E/D) |
Wifi | WiFi 802.11 b/g/n (AP6181) |
Storage | microSD card, SATA 2.0 |
USB | 2 x USB 2.0 host, 1 x USB 2.0 OTG |
GPIO header | 40 pins |
Banana Pi M1+
Status: fully supported (stable)
Remarks:
How to enable Wifi (depending on your kernel):
Kernel 3.4.x: Select the Banana Pi M1+ in 'bananian-hardware', add 'ap6210' to /etc/modules and reboot.
Kernel 4.x: Run 'aptitude install u-boot-pro-bananian' and reboot.
Name | Banana Pi M1+ |
---|---|
SoC | Allwinner A20 |
CPU | ARM Cortex-A7 Dual-Core 1GHz |
GPU | ARM Mali400 MP2 |
RAM | 1 GB DDR3 |
Ethernet | 1 x 10/100/1000Mbps (Realtek RTL8211E/D) |
Wifi | WiFi 802.11 b/g/n (AP6181) |
Storage | microSD card, SATA 2.0 |
USB | 2 x USB 2.0 host, 1 x USB 2.0 OTG |
GPIO header | 40 pins |
Banana Pi R1 (router)
Status: supported (stable)
Remarks:
See /etc/network/if-pre-up.d/swconfig for a basic switch/VLAN configuration.
Name | BPi-R1 |
---|---|
SoC | Allwinner A20 |
CPU | ARM Cortex-A7 Dual-Core 1GHz |
GPU | ARM Mali400 MP2 |
RAM | 1 GB DDR3 |
Ethernet | 5 x 10/100/1000Mbps (BCM53125) |
Wifi | WiFi 802.11 b/g/n (Realtek RTL8192CU) |
Storage | microSD card, SATA 2.0 |
USB | 1 x USB 2.0 host, 1 x USB 2.0 OTG |
GPIO header | 26 pins |
Banana Pi M2
Status: supported (beta)
Remarks:
Download and more information
Name | BPI-M2 |
---|---|
SoC | Allwinner A31S |
CPU | ARM Cortex-A7 Quad-Core 1GHz |
GPU | PowerVR SGX544MP2 |
RAM | 1 GB DDR3 |
Ethernet | 1 x 10/100/1000Mbps |
Wifi | WiFi 802.11 b/g/n |
Storage | microSD card |
USB | 4 x USB 2.0 host |
GPIO header | 40 pins |
Banana Pi M2+
Status: not supported yet
Remarks:
none
Name | BPI-M2+ |
---|---|
SoC | Allwinner H3 |
CPU | ARM Cortex-A7 Quad-Core 1,2GHz |
GPU | ARM Mali400 MP2 |
RAM | 1 GB DDR3 |
Ethernet | 1 x 10/100/1000Mbps |
Wifi | WiFi 802.11 b/g/n |
Storage | microSD card, 8GB EMMC (optional) |
USB | 2 x USB 2.0 host, 1 x USB 2.0 OTG |
GPIO header | 40 pins |
Banana Pi M3
Status: not supported yet
Remarks:
none
Name | BPI-M3 |
---|---|
SoC | Allwinner A83T |
CPU | ARM Cortex-A7 Octa-Core 1,8GHz |
GPU | PowerVR SGX544MP1 |
RAM | 2 GB DDR3 |
Ethernet | 1 x 10/100/1000Mbps |
Wifi | WiFi 802.11 b/g/n |
Storage | microSD card, eMMC, SATA 2.0 (USB 2.0 bridge) |
USB | 2 x USB 2.0 host, 1 x USB 2.0 OTG |
GPIO header | 40 pins |
A20-OLinuXIno-LIME2
Status: supported (beta)
Remarks:
Enable LIME2 script.bin (boot configuration).
This is required to boot Bananian.
- Insert your SD card into the card reader
- Mount the FAT partition: (replace sdx with your SD card block device name)
mount /dev/sdx1 /mnt
- Replace script.bin:
cp /mnt/fex/OLinuXIno-LIME2/script.bin /mnt/script.bin
- Unmount the FAT partition:
umount /mnt
- Boot the A20-OLinuXIno-LIME2 with Bananian
Name | A20-OLinuXIno-LIME2 |
---|---|
SoC | Allwinner A20 |
CPU | ARM Cortex-A7 Dual-Core 1GHz |
GPU | ARM Mali400 MP2 |
RAM | 1 GB DDR3 |
Ethernet | 1 x 10/100/1000Mbps |
Wifi | none |
Storage | microSD card, SATA 2.0 |
USB | 2 x USB 2.0 host, 1 x USB 2.0 OTG |
GPIO header | 160 pins |
Orange Pi
Status: supported (beta)
Remarks:
- No Wifi
Name | Orange Pi |
---|---|
SoC | Allwinner A20 |
CPU | ARM Cortex-A7 Dual-Core 1GHz |
GPU | ARM Mali400 MP2 |
RAM | 1 GB DDR3 |
Ethernet | 1 x 10/100/1000Mbps (Realtek RTL8211E) |
Wifi | WiFi 802.11 b/g/n (Realtek RTL8188ETV) |
Storage | microSD card, NAND (optional), SATA 2.0 |
USB | 4 x USB 2.0 host, 1 x USB 2.0 OTG |
GPIO header | 44 (18 + 26) pins |